LS2 Report: LHCb looks to future with SciFi detector


LHCb's new scintillating-fibre (SciFi) tracker
The new device’s modules are being assembled at the LHCb site
(Image: CERN)

For the LHCb detector at the Large Hadron Collider, the ongoing second long shutdown (LS2) of CERN’s accelerator complex will be a period of metamorphosis. After two successful data-collection runs, the detector is being upgraded to improve the precision of its physics measurements, many of which are the best in the world. There will therefore be five times more collisions every time proton bunches cross within the detector after LS2 and the LHCb collaboration plans on increasing the data-readout rate from 1 MHz to the LHC’s maximum interaction frequency of 40 MHz (or every 25 nanoseconds).

In addition to replacing nearly all of the electronics and data-acquisition systems to handle the enormous increase in data production, LHCb is replacing its tracking detectors with new ones, such as the scintillating-fibre tracker, or SciFi. The SciFi will be placed behind the dipole magnet of LHCb.

Scintillating fibres, as the name suggests, are optical fibres – with a polystyrene base, in this case – that emit tens of photons in the blue-green wavelength when a particle interacts with them. Secondary scintillator dyes have been added to the polystyrene to amplify the light and shift it to longer wavelengths so it can reach custom-made silicon photomultipliers (SiPM) that convert optical light to electrical signals. The technology has been well tested at other high-energy-physics experiments. The fibres themselves are lightweight, they can produce and transmit light within the 25-nanosecond window and they are suitably tolerant to the ionising radiation expected in the future.

Each scintillating fibre making up the sub-detector is 0.25 mm in diameter and nearly 2.5 m in length. The fibres will be packed into modules that will reside in three stations within LHCb, each made of four so-called “detection planes”, with the photomultipliers located at the top and bottom of each plane. “The fibres have been painstakingly examined, wound into multi-layer ribbons, assembled into detector modules and thoroughly tested,” explains Blake Leverington, who is coordinating part of the SciFi project for LHCb. “The fibres provide a single-hit precision better than 100 microns and the single-hit efficiency over the area of the detector is better than 99%.” In total, over 10 000 km of precision-made scintillating fibres will adorn LHCb.

Unlike the other LHC detectors, LHCb is asymmetric in design and studies particles that fly very close to the beam pipe after being produced in proton-proton collisions. However, operating a sensitive detector this close to the beam pipe brings its own problems. Simulations show that radiation damage from collision debris would darken the fibres closest to the beam pipe by up to 40% over the lifetime of LHCb. This would make it harder for the produced light to be transmitted through the fibres, but the detector is expected to remain efficient despite this.

The photomultipliers located at the top and bottom of each SciFi detection plane will be bombarded by neutrons produced in the calorimeters that sit further downstream. The radiation damage results in so-called “dark noise”, where thermally excited electrons cause the SiPMs to produce a signal that mimics the signal coming from individual photons. In addition to shielding placed between the SciFi and the calorimeters, a complex cooling system has been developed to chill the SiPMs. “Measurements have shown that the rate of dark noise can be reduced by a factor of two for every 10 °C drop in temperature,” points out Leverington. The SiPMs have been mounted on special 3D-printed titanium cold-bars that are cooled to −40 °C.

“The project has had contributions from more than a hundred scientists, students, engineers and technicians from 17 partner institutes in 10 countries,” says Leverington. “We have worked together for seven years to bring SciFi to life.” Currently, the SciFi modules, services and electronics are being assembled and installed in the 12 mechanical frames in the assembly hall at the LHCb site at Point 8 of the LHC ring. The first SciFi components are planned to be installed in spring next year.

/Public Release. View in full here.